Monitoring Storage Pool Health – GriffinMonitor Module

There have been times in the past (more than I like to remember) where I’ve had a hard drive fail, a raid 5 fail, and eventually I am sure I’ll have a Storage Pool fail at some point with my lab environment. The best way to avoid this is by introducing active and heavy monitoring. In my work world I am very good and forward thinking when it comes to this; however no matter how many times it happens in my home environment I still fail at maintaining the system.

When Server 2012 was released with the introduction of Storage Pools I had just lost my RAID 5, I decided it was the right time to implement Storage Pools as my primary storage at home. It uses parity which is basically a software raid, and I was able to use cheap consumer drives along with USB drives (YAY! more space since I was out of it inside of the server.)

I’ve been running Storage Pools for over a year, knowing one major issue with my setup. I have absolutely no monitoring in place, and if I were to have a drive fail it could be weeks… maybe months before I realize an issue exists. I recently went through updating my home lab from Server 2012 to 2012 R2 and decided I needed to stop fooling around with my data and get some monitoring in place.

Well the first issue came along… how am I going to monitor my Storage Pool? Sadly there is no easy alerting of an unhealthy Storage Pool built in… I’m sure there are third party tools, but do I really want to go through the hassle of setting that up for just my Storage Pool? The good news is that PowerShell has some fantastic cmdlet’s available for working with storage.

When I started building my monitoring solution I initially thought… a simple script on a scheduled task will get the job done. As I built it out, I decided that I needed to go further than I have in the past, I needed to build a cmdlet, then once I finished that I thought why stop there? Why not built my first module? This module currently only contains a single PowerShell cmdlet, but as time goes on I hope to build out many more that I can continue to use in my environment at home. Below is the entire source of the psm1 file that is stored in my Modules directory along with installation instructions and directions on how to use the cmdlet.

Using Alert-GMUnhealthyStoragePool:

This is a fairly straightforward cmdlet, only 3 mandatory parameters and it works. There are quite a few restrictions surrounding the SMTP Server including it cannot use TLS or SSL (Currently) and it doesn’t accept Authentication. These will be added in the future but for the first iteration of it I was going for quick and dirty for a lab environment.

Example:

ย The Module Code:

Installation Instructions:

  1. Navigate to C:\Users\<username>\Documents\WindowsPowerShell\Modules\GriffinMonitor
    1. (Note: If the directory doesn’t exists you must create it.)
  2. Save the above code in a file named GriffinMonitor.psm1 under the above directory
  3. Create a Scheduled Job using PowerShell

Once it is scheduled, keep an active eye on your inbox for when your Storage Pool goes unhealthy!

Miscellaneous Notes:

  • This module was built and tested using PowerShell v4 on Server 2012 R2 running a single Storage Pool.
  • This module “should” work with Server 2012 running PowerShell v3 with one or many Storage Pools
  • This module comes with no guarantee or support, this is a run at your own risk and I take no responsibility for any repercussions that may occur by running this.
    • With that being said I’ll try my best to assist anyone who may have questions if you post in the comments of this thread.
Be Sociable, Share!
  1. Great!

    Do you already have a plan when to expect smtp with authentication and tls ? would be realy handy ๐Ÿ™‚

  2. ๐Ÿ˜›

    Awesome! Realy cool! Could you help me to make a check? How can i test this if my smtp server uses port 444 for example?

    Best, Fab

    • If you are working on Server 2012 R2 you can use Test-NetConnection -Port 444 -ComputerName Server1 where ComputerName is the name of the computer listening on port 444.

Leave a Comment


NOTE - You can use these HTML tags and attributes:
<a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code class="" title="" data-url=""> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong> <pre class="" title="" data-url=""> <span class="" title="" data-url="">

Trackbacks and Pingbacks: